System 6000 MKII AlgorithmsEnglish Manual Applies to System 6000 firmware version 6.5.0 TC Icon version 7.5.0Last manual update: 2014-07-22
Introduction6 System 6000 MKII Algorithms – Firmware version 6.5.0Channel distribution in surround algorithmsTo best comply with the channel allocati
Reflector 6 & Reflector LCR96 System 6000 MKII Algorithms – Firmware version 6.5.0
Reflector 6 & Reflector LCREnglish Manual – Updated 2014-07-22 97Dynamics processing
Reflector 6 & Reflector LCR98 System 6000 MKII Algorithms – Firmware version 6.5.0
MD 5.1English Manual – Updated 2014-07-22 99MD5.1MD5.1 algorithm – introductionMD5.1 is a multi-channel multi-band expander/compressor algorithm,
MD 5.1100 System 6000 MKII Algorithms – Firmware version 6.5.0Hi XoverRange: Off to 16 kHzSets the Cross-over frequency between the Mid- and the Hi-
MD 5.1English Manual – Updated 2014-07-22 101Setting a channel to unprocessed will preserve the processing delay through the algorithm, keeping the
MD 5.1102 System 6000 MKII Algorithms – Firmware version 6.5.0AttackRange: 0.3 to 100 msSets the time it takes for the Expander to reach the attenua
MD 5.1English Manual – Updated 2014-07-22 103Example: If the Reference Level is set to -18dBFS, a Threshold setting of -4dB, will cause the com-pr
MD 5.1104 System 6000 MKII Algorithms – Firmware version 6.5.0Bypass LimiterPress to Bypass the Limiter section of the 5.1 algorithm.MD5.1 algorith
MD 5.1English Manual – Updated 2014-07-22 105ReleaseRange: 0.01 to 1.00 secondsRelease time for the Limiter.CeilingRange: 0 to -0.10dB in 0.01dB s
IntroductionEnglish Manual – Updated 2014-07-22 7Reverbs
MD 5.1106 System 6000 MKII Algorithms – Firmware version 6.5.0
MD-3English Manual – Updated 2014-07-22 107MD-3High resolution, multiband dynamics processing has been a trademark of TC Electronic for more than a d
MD-3108 System 6000 MKII Algorithms – Firmware version 6.5.0Please note that when coming from e.g. Dual Mono mode EQ settings from the Left channel w
MD-3English Manual – Updated 2014-07-22 109Output ModeRange: Left/Right, MSLeft/Right: Straight Output without MS Decode.MS: MS decode before the lim
MD-3110 System 6000 MKII Algorithms – Firmware version 6.5.0Basic operation ►Press keys Lo, Mid1, Mid2 and Hi to activate/deactivate the EQ bands. ►S
MD-3English Manual – Updated 2014-07-22 111Range – Hi band: 20 Hz to 40 kHzGainPress Gain and use Faders 1 to 4 to adjust gain for each of the four E
MD-3112 System 6000 MKII Algorithms – Firmware version 6.5.0Pressing Threshold, Range, Ratio, Attack and Release keys will immediately assign Lo, Mid
MD-3English Manual – Updated 2014-07-22 113Example: With a Ratio setting of 2:1 the com-pressor will reduce every 2dB above the Thresh-old point to
MD-3114 System 6000 MKII Algorithms – Firmware version 6.5.0Output FaderOutput FaderRange: Off to 0dB Off to -40dB: in 3dB steps, -40 to 0dB in
MD-4English Manual – Updated 2014-07-22 115MD-4MD-4 algorithm – introductionMD-4 is a multiband processor featuring newly developed DXP processing th
Introduction8 System 6000 MKII Algorithms – Firmware version 6.5.0
MD-4116 System 6000 MKII Algorithms – Firmware version 6.5.0convenient place to adjust more or less dynam-ics processing and Loudness.Trim offers the
MD-4English Manual – Updated 2014-07-22 117When mastering with DXP mode, start with a Reference Level around -8 dBFS. This will en-sure that loud pa
MD-4118 System 6000 MKII Algorithms – Firmware version 6.5.0(wide=S) such as ambience, or to treat fully cor-related components (center=M) in a certa
MD-4English Manual – Updated 2014-07-22 119When set to 0.0 ms, the delay through MD4 caused by additional look ahead structures and up-sampling, amou
MD-4120 System 6000 MKII Algorithms – Firmware version 6.5.0MD-4 algorithm – 5 band pageMD-4 algorithm – 5 band page5Band Compressor Fader GroupsThe
MD-4English Manual – Updated 2014-07-22 121Threshold L – Threshold RRange: -12 to 0dBFSOutput Limiter Thresholds. Consider linking L and R when used
MD-4122 System 6000 MKII Algorithms – Firmware version 6.5.0
MDX5.1English Manual – Updated 2014-07-22 123MDX5.1MDX5.1 algorithm – introductionMDX5.1 is a high resolution dynamics processor for multichannel
MDX5.1124 System 6000 MKII Algorithms – Firmware version 6.5.0for instance, different settings for the Center or Surround channels, where speech int
MDX5.1English Manual – Updated 2014-07-22 125ference between the two, for instance 15dB or more.If the delivery resolution is low, the difference s
TC reverb algorithms: an introductionEnglish Manual – Updated 2014-07-22 9TC reverb algorithms: an introductionThe TC Reverb PaletteUntil 15 to 20 y
MDX5.1126 System 6000 MKII Algorithms – Firmware version 6.5.0Input OutputLE1 E2 E3 E4LR RC CLFE LFESL SLSR SRXtMDX5.1 algorithm – main pageMDX5.1
MDX5.1English Manual – Updated 2014-07-22 127can be less than 16 kHz if the Hi Xover parameter is set below 16 kHz.Hi XoverRange: Off to 16 kHzSets
MDX5.1128 System 6000 MKII Algorithms – Firmware version 6.5.0NormalRange: Off / OnWhen this parameter is set to “On” the Input channels selected to
MDX5.1English Manual – Updated 2014-07-22 129Soft ClipFull Range SoftClipRange: 6dB to +3dB to OffSoftclipper Threshold setting after the Compres-
MDX5.1130 System 6000 MKII Algorithms – Firmware version 6.5.0MDX5.1 algorithm – output pageMDX5.1 algorithm – output pageTrim LevelsOutput trimsR
MDX5.1English Manual – Updated 2014-07-22 131EQs
MDX5.1132 System 6000 MKII Algorithms – Firmware version 6.5.0
EQ -5.1English Manual – Updated 2014-07-22 133EQ-5.1The EQ 5.1 algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate: 1/4
EQ -5.1134 System 6000 MKII Algorithms – Firmware version 6.5.0EQ-5.1 algorithm – front / center / surround / LFE pagesEQ-5.1 algorithm – front pageP
EQ -5.1English Manual – Updated 2014-07-22 135Cut Filter – Butterworth typeFreqPress Freq and use Faders 1 to 4 to adjust fre-quencies for each of th
TC reverb algorithms: an introduction10 System 6000 MKII Algorithms – Firmware version 6.5.0Source ReverbWhen elements of a mix are picked up individ
EQ -5.1136 System 6000 MKII Algorithms – Firmware version 6.5.0
Massenburg (MDW) EQEnglish Manual – Updated 2014-07-22 137Massenburg (MDW) EQThe MDW Hi Res EQ 2 channel algorithm oc-cupies: ►@ Normal Sample Rate
Massenburg (MDW) EQ138 System 6000 MKII Algorithms – Firmware version 6.5.0been established. Now a Relative link can be enabled, preserving the adjus
Massenburg (MDW) EQEnglish Manual – Updated 2014-07-22 1396-ch. versionIn the 6-ch. version a Channel select parameter is placed below the Output me
Massenburg (MDW) EQ140 System 6000 MKII Algorithms – Firmware version 6.5.06 channel versionThe Gain parameters are located at the Level page.When Li
Massenburg (MDW) EQEnglish Manual – Updated 2014-07-22 141Format conversion
Massenburg (MDW) EQ142 System 6000 MKII Algorithms – Firmware version 6.5.0
DMixEnglish Manual – Updated 2014-07-22 143DMixDMix: Optimum Mobile Platform DeliveryIn just one engine, DMix can downmix, loudness process and true-
DMix144 System 6000 MKII Algorithms – Firmware version 6.5.0true-peak limiting performed at 48 bit, fixed point precision. This enables the downmix g
DMixEnglish Manual – Updated 2014-07-22 145the Loudness Control cannot attenuate the sig-nal at all.Max GainRange: 0 to +20dBThis is the maximum gai
Core-2English Manual – Updated 2014-07-22 11Core-2The TC Electronic REV CORE algorithms are particularly good for small room simulations. Due to the
DMix146 System 6000 MKII Algorithms – Firmware version 6.5.0the Output level is close to the Target Level, gain changes are relatively slow.The Avera
DMixEnglish Manual – Updated 2014-07-22 147Cut Filter – Bessel typeCut Filter – Butterworth typeFreqPress Freq and use Faders 1 to 3 to adjust the fr
DMix148 System 6000 MKII Algorithms – Firmware version 6.5.0Range: ►Xover 1: Off to 1,6 kHz ►Xover 2: Off to 4 kHz ►Xover 3: 100 Hz to Of, ►Xover 4:
DMixEnglish Manual – Updated 2014-07-22 149levels, e.g. when preparing film or concerts for domestic or noisy environment listening.Try setting the S
DMix150 System 6000 MKII Algorithms – Firmware version 6.5.0bution, and not to process more than necessary for a certain broadcast platform. Don’t ta
Unwrap HDEnglish Manual – Updated 2014-07-22 151Unwrap HDThe UnWrap HD algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample
Unwrap HD152 System 6000 MKII Algorithms – Firmware version 6.5.0This way you can check all speakers one by one with pink noise first, and also colla
Unwrap HDEnglish Manual – Updated 2014-07-22 153Then choose between the four Contour Styles, and finally apply EQ to the center channel if de-sired.
Unwrap HD154 System 6000 MKII Algorithms – Firmware version 6.5.0LFE ProcessingLFE Hi Cut FrequencyRange: 10 to 200 HzSets the Hi Cut frequency for t
Unwrap HDEnglish Manual – Updated 2014-07-22 155Range for the Shelve filter: ►Lo BW: 3 to 12dB/oct ►Hi BW: 3 to 12dB/octRange for the Cut filter:
Core-212 System 6000 MKII Algorithms – Firmware version 6.5.0In LevelRange: Off to 0.0dBSets the level of the Input to the Reverb in 0.5dB steps.Ou
Unwrap HD156 System 6000 MKII Algorithms – Firmware version 6.5.0Range for the Notch filter: ►Lo BW: 0.02 to 1 oct ►Mid1BW: 0.02 to 1 oct ►Mid2BW:
Unwrap HDEnglish Manual – Updated 2014-07-22 157Limiting
Unwrap HD158 System 6000 MKII Algorithms – Firmware version 6.5.0
Brickwall 2English Manual – Updated 2014-07-22 159Brickwall 2The Brickwall Limiter occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sampl
Brickwall 2160 System 6000 MKII Algorithms – Firmware version 6.5.0ting, internal variables other than Release Time will be fixed.Absolute Bit Transp
Brickwall 2English Manual – Updated 2014-07-22 161More information… About 0dBFS+ signals, required headroom in the signal path, behavior of consume
Brickwall 2162 System 6000 MKII Algorithms – Firmware version 6.5.0subsequently low bit-rate data reduced. In such cases try around -2dBFS, and list
Brickwall 2English Manual – Updated 2014-07-22 163Brickwall 2 algorithm – setup pageBrickwall 2 algorithm – setup pageTimingDelayFor alignment two D
Brickwall 2164 System 6000 MKII Algorithms – Firmware version 6.5.0
Brickwall 2English Manual – Updated 2014-07-22 165Loudness correction
Core-2English Manual – Updated 2014-07-22 13DiffuseRange: -50 to 50This parameter gives you more or less Diffusion than the algorithm designer intend
Brickwall 2166 System 6000 MKII Algorithms – Firmware version 6.5.0
ALC 6English Manual – Updated 2014-07-22 167ALC 6ALC6 is an automatic loudness adjustment pro-cessor for mono, stereo, LtRt and 5.1 formats. It is a
ALC 6168 System 6000 MKII Algorithms – Firmware version 6.5.0ALC6 – main pageFig 1. TC Icon view of ALC6 Main page parameters.Preset titleThe Main pa
ALC 6English Manual – Updated 2014-07-22 169ALC6 – ALC pageFig 3: ALC6 algorithm – ALC pageTarget LevelTarget Level sets the Loudness Target aimed f
ALC 6170 System 6000 MKII Algorithms – Firmware version 6.5.0rides Corrections when the input level is higher than Target.Stridency ReductionAs consu
ALC 6English Manual – Updated 2014-07-22 171ALC6 – Limit pageThe Limiter in ALC6 uses true-peak detection exceeding the oversampling requirements of
ALC 6172 System 6000 MKII Algorithms – Firmware version 6.5.0threshold is exceeded on the LFE channel, LFE is limited independently.C, LR, LFEIf the
ALC 6English Manual – Updated 2014-07-22 173ALC6 used for Transmission 1. Load a suitable ALC6 preset, then follow these directions in the given or
ALC 6174 System 6000 MKII Algorithms – Firmware version 6.5.0ALC6 used for Ingest 1. Load a suitable ALC6 preset, then follow these directions in th
ALC 6English Manual – Updated 2014-07-22 175ALC6 used for Live ProductionBecause of its low latency (0.8 ms, equivalent to the time it takes sound t
Core-214 System 6000 MKII Algorithms – Firmware version 6.5.0
ALC 6176 System 6000 MKII Algorithms – Firmware version 6.5.0
ALC 6English Manual – Updated 2014-07-22 177Loudness radar meters
ALC 6178 System 6000 MKII Algorithms – Firmware version 6.5.0
LM6English Manual – Updated 2014-07-22 179LM6LM6 represents a quantum leap away from sim-ply measuring audio level to measuring per-ceived loudness.
LM6180 System 6000 MKII Algorithms – Firmware version 6.5.0tion with long-term descriptors from production onwards, is a transparent and well soundin
LM6English Manual – Updated 2014-07-22 181conditions etc using normal DB4 and DB8 preset handling procedures.Radar pageCurrent Loudness: Outer RingTh
LM6182 System 6000 MKII Algorithms – Firmware version 6.5.0rely on this parameter may take place in the con-sumer’s receiver. Therefore, its value sh
LM6English Manual – Updated 2014-07-22 183This may be regarded as initial production guide-lines: ►HDTV and digital radio: Stay below LRA of 20 LU. ►
LM6184 System 6000 MKII Algorithms – Firmware version 6.5.0TargetRange: -36 LUFS to -6 LUFSThe parameter specifies the loudness level to generally ai
LM6English Manual – Updated 2014-07-22 185genres. BS.1770-2 enables the meter reliably to focus on foreground sound, and to transparently control lou
DVR-2English Manual – Updated 2014-07-22 15DVR-2IntroductionDVR-2 offers Reverb and System 6000 users a pristine Generic Reverb with true vintage fla
LM6186 System 6000 MKII Algorithms – Firmware version 6.5.0Stereo or 5.1 IntegrityIn this mode, Integrity is given when either Ste-reo or 5.1 Integri
LM6English Manual – Updated 2014-07-22 187built into the standard. The final BS.1770 stan-dard included a multichannel annex with a re-vised weightin
LM6188 System 6000 MKII Algorithms – Firmware version 6.5.0Post ScriptControl of loudness is the only audio issue that has made It to the political a
LM6English Manual – Updated 2014-07-22 189Mixing
LM6190 System 6000 MKII Algorithms – Firmware version 6.5.0
Matrix 88English Manual – Updated 2014-07-22 191Matrix 88Features ►8x8 48 bit mixer algorithm ►Precision delay on all inputs and outputs ►2 stereo
Matrix 88192 System 6000 MKII Algorithms – Firmware version 6.5.0Ch1 / Ch2 / Ch3InvPhase inverse for each input.Delay 1 to 3Range: 0 to 333 ms / 0
Matrix 88English Manual – Updated 2014-07-22 193input and output faders also operate in the 48 bit domain, thereby enabling loss-free cut and even b
Matrix 88194 System 6000 MKII Algorithms – Firmware version 6.5.0Main OutputsDelay Main A/BRange: 0 to 333 ms / 0 to 14700 smp / 0 to 111 m / 0 t
Matrix 88English Manual – Updated 2014-07-22 195Modulation effects
DVR-216 System 6000 MKII Algorithms – Firmware version 6.5.0ReverbDecayRange: 0.2 to 4.5 sAdjusts the Master Decay time.xLoRange: 0.5 to 2.0Decay mul
Matrix 88196 System 6000 MKII Algorithms – Firmware version 6.5.0
Chorus-1English Manual – Updated 2014-07-22 197Chorus-1The Chorus algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate:
Chorus-1198 System 6000 MKII Algorithms – Firmware version 6.5.0Feedback Hi CutRange: 1 kHz to offFeedback Hi Cut enables you to remove high fre-quen
Phaser-1English Manual – Updated 2014-07-22 199Phaser-1The Phaser-1 algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate
Phaser-1200 System 6000 MKII Algorithms – Firmware version 6.5.0MixRange: 0 to 100 %Mixes between direct sound and phaser sound.
Phaser-1English Manual – Updated 2014-07-22 201Noise reduction
Phaser-1202 System 6000 MKII Algorithms – Firmware version 6.5.0
BackdropEnglish Manual – Updated 2014-07-22 203BackdropThe BackDrop algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate
Backdrop204 System 6000 MKII Algorithms – Firmware version 6.5.0signal. For certain stereo audio sequences, op-erating in M/S mode can give better re
BackdropEnglish Manual – Updated 2014-07-22 205The Max Reduction parameter tells BackDrop the maximum amount of noise reduction you are trying to ach
DVR-2English Manual – Updated 2014-07-22 17Input TransEmulates the sound of Input transformers typi-cally used in vintage Reverbs. Use it to create a
Backdrop206 System 6000 MKII Algorithms – Firmware version 6.5.0MultiBand ModelBackdrop algorithm – MultiBand model pageThe MultiBand model offers an
BackdropEnglish Manual – Updated 2014-07-22 207is often dominated by lower frequency noise. Fi-nally, the Hiss component consists of the broad-band n
Backdrop208 System 6000 MKII Algorithms – Firmware version 6.5.0print information based on the audio contained between the Trim Start and Trim End po
BackdropEnglish Manual – Updated 2014-07-22 209put signal is relatively high, you will likely begin to hear strange low-level random chirping sounds.
Backdrop210 System 6000 MKII Algorithms – Firmware version 6.5.0Max Reduction to 0 dB. Slowly increase Max Reduction and listen as the level of nois
BackdropEnglish Manual – Updated 2014-07-22 211Backdrop algorithm – frequently asked questionsIs it better to get as long a noise print as possible?T
Backdrop212 System 6000 MKII Algorithms – Firmware version 6.5.0
BackdropEnglish Manual – Updated 2014-07-22 213Panning
Backdrop214 System 6000 MKII Algorithms – Firmware version 6.5.0
SpacePan 5.1English Manual – Updated 2014-07-22 215SpacePan 5.1The SpacePan 5.1 algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Doubl
DVR-218 System 6000 MKII Algorithms – Firmware version 6.5.0
SpacePan 5.1216 System 6000 MKII Algorithms – Firmware version 6.5.0The parameters for each of the 8 sources can be adjusted as follows:With the Fade
SpacePan 5.1English Manual – Updated 2014-07-22 217Pitch processing
SpacePan 5.1218 System 6000 MKII Algorithms – Firmware version 6.5.0
VP-2 StereoEnglish Manual – Updated 2014-07-22 219VP-2 StereoThe VP-2 Stereo algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double S
VP-2 Stereo220 System 6000 MKII Algorithms – Firmware version 6.5.0Factor/AdjustRange: 1, 10 or 100The Factor parameter is a multiplier factor for th
VP-2 StereoEnglish Manual – Updated 2014-07-22 221Cross L to RRange: 0 to 100 %The percentage of processed signal from the al-gorithm’s left Output
VP-2 Stereo222 System 6000 MKII Algorithms – Firmware version 6.5.0
VP-8English Manual – Updated 2014-07-22 223VP-8The VP-8 Stereo algorithm occupies: ►@ Normal Sample Rate: 2/4 DSP Resource ►@ Double Sample Rate: not
VP-8224 System 6000 MKII Algorithms – Firmware version 6.5.0For non-music applications, you may prefer to keep the LFE channel free of any transposin
VP-8English Manual – Updated 2014-07-22 225Factor/AdjustRange: 1, 10 or 100The Factor parameter is a multiplier factor for the Adjust handles. Use th
NonLin2English Manual – Updated 2014-07-22 19NonLin2IntroductionNonLin2 is an Effect Reverb with controllable En-velope, Attack, Hold and Release. It
VP-8226 System 6000 MKII Algorithms – Firmware version 6.5.0
NonLin220 System 6000 MKII Algorithms – Firmware version 6.5.0and unnatural effect is obtained at short Release settings.Max. range for this paramete
NonLin2English Manual – Updated 2014-07-22 21Wet LevelRange: Off to 0dBAdjusts the wet Output level.Lo CutRange: 20 Hz to 20 kHzLo Cut on the Reverb
NonLin222 System 6000 MKII Algorithms – Firmware version 6.5.0
Reverb-2English Manual – Updated 2014-07-22 23Reverb-2The Reverb 2 algorithm initially created for the TC M5000 compliments most types of source mate
Reverb-224 System 6000 MKII Algorithms – Firmware version 6.5.0Out LevelRange: -100dB to 0dBSets the Output level of the.Reverb-2 algorithm – rever
Reverb-2English Manual – Updated 2014-07-22 25Hi DecayRange: 0.01 to 2.00 timesMultiplier for the high frequencies. If Hi Decay e.g. is set to 0.5, t
English Manual – Updated 2014-07-22 aAbout this manual 1Algorithms overview 2Introduction 5REVERBS 7TC reverb algorithms: an introduction 9Core
Reverb-226 System 6000 MKII Algorithms – Firmware version 6.5.0
Reverb-3English Manual – Updated 2014-07-22 27Reverb-3This is a description of the parameters specific to the Reverb-3 algorithm. It is capable of ma
Reverb-328 System 6000 MKII Algorithms – Firmware version 6.5.0Hi Cut FreqRange: 500 Hz to flatHi Cut filter, shelving type. Provides an over-all Rev
Reverb-3English Manual – Updated 2014-07-22 29DepthRange: 0 to 100 %Controls the amount of delay path modulation or “wander” in the Reverb. The contr
Reverb-330 System 6000 MKII Algorithms – Firmware version 6.5.0
Reverb8English Manual – Updated 2014-07-22 31Reverb8IntroductionReverb 8 is a new reverb algorithm for System 6000 MKII. It has been developed for
Reverb832 System 6000 MKII Algorithms – Firmware version 6.5.0 ►9: Front L, FL ►10: Front R, FR ►11: Front Center, FC ►12: Back Center, BC ►13: Back
Reverb8English Manual – Updated 2014-07-22 33Reverb8 essentialsReverb8 is supposed to cover an endless vari-ety of formats and channel counts. Thi
Reverb834 System 6000 MKII Algorithms – Firmware version 6.5.0Using Reverb8Load one of the Reverb8 presets into an Engine and go to its Main page
Reverb8English Manual – Updated 2014-07-22 35Grid setup – Res. parametersWhat happens when the dot in the Grid is moved off-center is defined on the
Reverb836 System 6000 MKII Algorithms – Firmware version 6.5.0Working with multiple Reverb 8 instancesWith more than one Engine running Reverb 8, i
Reverb8English Manual – Updated 2014-07-22 37Mute Group 1 & Mute Group 2 buttonUse the Mute Group 1 & Mute Group 2 buttons to temporarily mu
Reverb838 System 6000 MKII Algorithms – Firmware version 6.5.0Lo DecayRange: 0.5 to 2.0Use the Lo Decay parameter to define the decay time for the l
Reverb8English Manual – Updated 2014-07-22 39Reverb 8 algorithm – Setup pageFig13. Reverb 8 algorithm – Setup pageGrid Setup sectionDecay Res.Setti
Reverb840 System 6000 MKII Algorithms – Firmware version 6.5.0Group 1 sectionUse the Group 1 section of the Setup page to specify the Reverb channel
Reverb8English Manual – Updated 2014-07-22 41NHK channel assignmentsThe NHK 22.2 settings have been tuned for op-timized performance with these chan
Reverb842 System 6000 MKII Algorithms – Firmware version 6.5.0Rev page – Reverb Color sectionLo DampRange: -18 to 0dBReverb8 is equipped with an a
Reverb8English Manual – Updated 2014-07-22 43Reverb8 algorithm – Trim pageFig15. Reverb8 algorithm – Trim pageLevel trims and Delay offsets per o
Reverb844 System 6000 MKII Algorithms – Firmware version 6.5.0
VSS™3English Manual – Updated 2014-07-22 45VSS™3The VSS™3 Reverb algorithm incorporates dedi-cated Early Reflection types for motion picture use, e
About this manualEnglish Manual – Updated 2014-07-22 1About this manualThis manual will help you learn understanding and operating your TC product.T
VSS™346 System 6000 MKII Algorithms – Firmware version 6.5.0Out LevelRange: -100dB to 0dBThe overall Output level of the Reverb. This is mostly us
VSS™3English Manual – Updated 2014-07-22 47middle, Stereo is the normal stereo image width and Wide covers the outside of the stereo image.The RevTy
VSS™348 System 6000 MKII Algorithms – Firmware version 6.5.0Hi DecayRange: 0.01 to 2.5Multiplier for the frequencies above the Hi Xover frequency. E
VSS™4English Manual – Updated 2014-07-22 49VSS™4IntroductionVSS™4 is a True Stereo Reverb – or two Source Input to Stereo Output reverb – and radi
VSS™450 System 6000 MKII Algorithms – Firmware version 6.5.0Reverb TypeRange: Normal or ColoredWhen a Location Type is selected a Reverb type is aut
VSS™4English Manual – Updated 2014-07-22 51VSS™4 algorithm – setup pageVSS™4 algorithm – setup pageLocation TypeLocation TypeSelect between differ
VSS™452 System 6000 MKII Algorithms – Firmware version 6.5.0Example: When a Decay multiplier is set to 1.25 and the Master Decay is 2.0 seconds the
VSS™ 5.1 SourceEnglish Manual – Updated 2014-07-22 53VSS™ 5.1 SourceChoosing between VSS™ 5.1 Source and VSS™ 5.1 reverb ►If you wish to add reverb
VSS™ 5.1 Source54 System 6000 MKII Algorithms – Firmware version 6.5.0Lo ColorRange: ±50Adjusts the low frequency spectrum for the com-pleteOutput. T
VSS™ 5.1 SourceEnglish Manual – Updated 2014-07-22 55Center ChannelRange: Off/On/Phantom OnThis parameter enables on/off setting of the Center speak
Algorithms overview2 System 6000 MKII Algorithms – Firmware version 6.5.0Algorithms overviewThis is an overview of the algorithms in the vari-ous Sys
VSS™ 5.1 Source56 System 6000 MKII Algorithms – Firmware version 6.5.0Source 1 to 4 Early ReflectionsLo ColorRange: ±50Adjusts the low frequency spec
VSS™ 5.1 SourceEnglish Manual – Updated 2014-07-22 57Will not be available when Output Mode is set to Stereo.Mid ColorRange: ±50Additional Color adj
VSS™ 5.1 Source58 System 6000 MKII Algorithms – Firmware version 6.5.0Reverb ModulationModulation TypeSelect between different types of modulation on
VSS™ 6.1 ReverbEnglish Manual – Updated 2014-07-22 59VSS™ 6.1 ReverbChoose your reverb wisely!Make sure to read the Reverb Intro chapter of this man
VSS™ 6.1 Reverb60 System 6000 MKII Algorithms – Firmware version 6.5.0Surr. Hi CutRange: 20 Hz to 20 kHzHi Cut parameter for the Reverb Diffuse field
VSS™ 6.1 ReverbEnglish Manual – Updated 2014-07-22 61LocationLocation TypeSelect between different Locations. Both the Early Reflection and Diffuse
VSS™ 6.1 Reverb62 System 6000 MKII Algorithms – Firmware version 6.5.0Hi CutRange: 20 Hz to 20 kHzDetermines the Hi Cut frequency.Hi SoftenRange: -50
VSS™ 6.1 ReverbEnglish Manual – Updated 2014-07-22 63Channel DecayThe following parameters are Decay multipliers for the diffuse responses. The mult
VSS™ 6.1 Reverb64 System 6000 MKII Algorithms – Firmware version 6.5.0Early StartRange: 0 to 100 %Adjusting the Start time is an efficient way of get
VSS™M4English Manual – Updated 2014-07-22 65VSS™M4IntroductionMultiple mono reverbs may often be more use-ful than pre-configured structures for st
Algorithms overviewEnglish Manual – Updated 2014-07-22 3LicenseMultichannel MasteringStereo MasteringMultichannel ReverbStereo ReverbLive AidLM6UnWr
VSS™M466 System 6000 MKII Algorithms – Firmware version 6.5.0VSS™M4 algorithm – levels pageVSS™M4 algorithm – levels pageIn Level (Reverb 1 to 4)R
VSS™M4English Manual – Updated 2014-07-22 67Reverb Lo/HiCutLo CutRange: 20 Hz to 200 HzDetermines the Lo Cut frequency. Attenuation amount is contro
VSS™M468 System 6000 MKII Algorithms – Firmware version 6.5.0
VSS™SREnglish Manual – Updated 2014-07-22 69VSS™SRThe VSS™SR (Surround) algorithm is a unique room simulator with new facilities for 4:2:4 sur-rou
VSS™SR70 System 6000 MKII Algorithms – Firmware version 6.5.0Front LevelRange: Off to 0dBChanges the level of the Front/Center informa-tion in the
VSS™SREnglish Manual – Updated 2014-07-22 71VSS™SR algorithm – reverb pageVSS™SR algorithm – reverb pageRev TypeRange: Smooth, Natural, Metal, Fas
VSS™SR72 System 6000 MKII Algorithms – Firmware version 6.5.0Mid XoverRange: 200 Hz to 2 kHzSets the frequency at which the transition from the low-
VSS™SREnglish Manual – Updated 2014-07-22 73Surround production tools
VSS™SR74 System 6000 MKII Algorithms – Firmware version 6.5.0
EngageEnglish Manual – Updated 2014-07-22 75EngageEngage algorithm – introductionThe Engage algorithm deals with three-dimen-sional sound reproductio
Algorithms overview4 System 6000 MKII Algorithms – Firmware version 6.5.0
Engage76 System 6000 MKII Algorithms – Firmware version 6.5.0Input TrimLeftRange: Off to 0dBLevel control for the left channel.CenterRange: Off to 0
Toolbox 5.1English Manual – Updated 2014-07-22 77Toolbox 5.1Toolbox 5.1 is designed to support surround pro-duction. The algorithm offers different
Toolbox 5.178 System 6000 MKII Algorithms – Firmware version 6.5.0Note that the Bass management is placed before this format conversion in the signal
Toolbox 5.1English Manual – Updated 2014-07-22 79channels. The Bass Management is placed just before the Output Format conversion.Main ChannelsLo Cu
Toolbox 5.180 System 6000 MKII Algorithms – Firmware version 6.5.0Ref Level 1, 2 and 3Range -100 to 0dBFor convenient switching between 3 different
Toolbox 5.1English Manual – Updated 2014-07-22 81De-Essing
Toolbox 5.182 System 6000 MKII Algorithms – Firmware version 6.5.0
De-EsserEnglish Manual – Updated 2014-07-22 83De-EsserThe De-Ess algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate: 1
De-Esser84 System 6000 MKII Algorithms – Firmware version 6.5.0Side ChainPressing Sidechain enables to monitor the part of the signal that is defined
De-EsserEnglish Manual – Updated 2014-07-22 85Delays
IntroductionEnglish Manual – Updated 2014-07-22 5IntroductionSystem 6000 contains a wealth of algorithms, and the list of algorithms will continuousl
De-Esser86 System 6000 MKII Algorithms – Firmware version 6.5.0
Delay-1English Manual – Updated 2014-07-22 87Delay-1The Delay-1 algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate: 1/
Delay-188 System 6000 MKII Algorithms – Firmware version 6.5.0
Delay-2English Manual – Updated 2014-07-22 89Delay-2The Delay-2 algorithm occupies: ►@ Normal Sample Rate: 1/4 DSP Resource ►@ Double Sample Rate: 1/
Delay-290 System 6000 MKII Algorithms – Firmware version 6.5.0Delay-2 algorithm – FB Modulation pageFeedback-1Range: -100 to 100 %The percent of posi
Reflector 6 & Reflector LCREnglish Manual – Updated 2014-07-22 91Reflector 6 & Reflector LCRThe Reflector-LCR algorithm occupies: ►@ Normal
Reflector 6 & Reflector LCR92 System 6000 MKII Algorithms – Firmware version 6.5.0Delay MultiplierThis parameter multiplies the value of the 24 i
Reflector 6 & Reflector LCREnglish Manual – Updated 2014-07-22 93The panner response depends on selected out-put format.X-PositionAdjusts the X-
Reflector 6 & Reflector LCR94 System 6000 MKII Algorithms – Firmware version 6.5.0FeedbackFeedback parameter from 0 to 100 %.Note 1:When a * symb
Reflector 6 & Reflector LCREnglish Manual – Updated 2014-07-22 95Reflector algorithms – Taps – shade pageReflector algorithms – Taps – shade pag
Kommentare zu diesen Handbüchern